Printing a mail job can be expensive, but postage is often one of the biggest costs on a mail job. An in-plant printing operation often receives jobs from other departments after they have already designed and approved the piece. The department is often in love with the piece and does not realize the cost of postage until the job is printed.
Credit: Pexels by Element5 Digital
If your in-plant does mailing as well as printing, then you are in a great position to catch many of these problems before they get to be too expensive. Here is the math that I would like to show to every department before a job is printed.
What Six Increases Did to a First-Class Run
The U.S. Postal Service increased the cost of a First-Class stamp six times between January 2023 and July 2026. A 1-oz. stamped letter increased from $0.60 to $0.82.
For a 5,000-piece stamped mailing, that would be the difference between $3,000 and $4,100 in postage. And the departments that set their budgets for mailing a few years ago are starting to run short on postage. The in-plant may be the first to hear about it.
The full price list can be found in USPS Notice 123. This is the place to look for the current numbers of all mail classes. It is very useful to have this page bookmarked.
Live Stamps, Meter or Permit?
The options for postage on mail pieces are each used for different purposes. The right one depends on the job, not habit.
The most expensive postage option for a 1-oz. letter is a live stamp at $0.82 each. The use of a live stamp on a letter conveys the personal touch of a letter sent by a president, dean, or other executive, an event invitation, or a major donor letter. Even though a piece of mail may have been printed in quantity, the use of a live stamp can create the impression that the piece was individually addressed and mailed.
Metered postage for a 1-oz. First-Class letter is $0.78 per piece. This is four cents less than the cost of a stamp for a single piece. For routine First-Class mail such as notices, statements, and letters, this can add up to a lot of money over the course of a year. For example, 5,000 pieces of metered mail will cost $3,900 as opposed to $4,100 for stamped mail.
The lowest per-piece rate for postage is for permit imprint with USPS Marketing Mail. However, there are conditions for using this rate.
- First, the mailing must consist of at least 200 pieces or 50 lbs.
- Second, a permit must be obtained and an annual fee paid.
- Third, the mail must be presorted and the rate of postage is dependent upon the sort level, so check Notice 123 for current prices. The mail is also slower than First-Class mail and is not forwarded unless forwarding is paid for. Thus, this rate is best used for large appeals, newsletters and recruitment mailings that are not time-sensitive.
For internal customers, stamps can be used when sending correspondence that needs to be personal. Meter is used for routine First-Class correspondence. Permit is used when sending large volumes of mail with flexible timing.
Design Details That Quietly Add Cost
Two overlooked design problems often are identified just as the mail is ready to be printed and mailed by the in-plant.
Square and rigid pieces. USPS sorting equipment processes mail that is rectangular and can bend. So, square envelopes, rigid mailpieces, or mailpieces that are lumpy from a seal, ribbon, or insert that does not bend will be charged a $0.49 nonmachinable surcharge per piece. For example, a mailing of 1,000 square invitations would cost $490 more in postage than the same mailing in rectangular envelopes.
The second ounce. First-Class letter prices are $0.82 for the first ounce and $0.29 for each additional ounce. A 2-oz. letter is $1.11, 3 oz. is $1.40, and 3.5 oz. is $1.69, the most a letter can weigh. Any heavier paper stock, extra insert, or reply card added to a letter can put it over the line without anyone noticing. Each piece over the line will cost an additional 29 cents.
Either choice is fine as long as the department is aware of the cost prior to having the piece printed.
A pre-press postage checklist
I would ask the department the following questions before printing a mail job.
- Shape: Is the piece rectangular, flexible, and an even thickness? If not, add $0.49 per piece.
- Weight: Has someone weighed a finished sample, with every insert, on the actual paper stock?
- Postcard option: Would a postcard do the job? A stamped postcard is $0.65.
- Mail class: Is the piece time-sensitive, or could it go via Marketing Mail? Does the run meet the 200-piece or 50-pound minimum?
- Postage method: Does the piece need the personal look of a stamp, or will metered postage serve?
- Budget: Is the department's postage estimate based on current rates, or on a number from a few years ago?
A five-minute conversation with the department at the proof stage can be worth hundreds or thousands of dollars in savings on a single mailing. This conversation also allows the in-plant to be the experts on print and postage, and to see the cost of design decisions before they are locked in.
- Categories:
- Mailing/Fulfillment - Postal Trends






